SKU
06VIPESI

Socket & See VIPESI Electrical Service Industry Safety Two Pole Tester

Add to Wish List Email to a Friend
This is the VIP ESI which is the culmination of over two years’ worth of development and field trials within several of the UK’s leading SMART Metering and Utility companies. Metering Companies face similar problems when checking the installation at the meter.
US$122.44
Add to Compare

Product Specification unless deselected above

More Information
Available Outside the UK? Yes
Brand Socket and See

Socket & See VIPESI Electrical Service Industry Safety Two Pole Tester

This is the VIP ESI which is the culmination of over two years’ worth of development and field trials within several of the UK’s leading SMART Metering and Utility companies. Metering Companies face similar problems when checking the installation at the meter.

Possible Problems

  • During meter installation the engineer does not know if the new meter has created a dead short which could lead to significant danger when energising the system.
  • An engineer arrives to find the main service cut out fuse has blown. He can’t see any other issues so the fuse is replaced. If a further problem is present then there is again significant danger when re-energising.
  • The Distribution Network Operators (DNO) face similar problems: They may be left to make the final connection to a newly built property, or where a new supply is to be connected to a new intake position. They might also need to reconnect a newly installed meter following an upgrade to the main supply cable and / or the cut-out.
  • The engineer arrives to fit a new consumer unit. How are the checks carried out to ensure it has been connected correctly and that there are no dead shorts in existence prior to energising at the meter?


The Solution

It solves all the above problems and creates much safer working practices than are currently available with any other know 2 pole testers. They can carry out a physical Impedance check to indicate hi or low Impedance on the circuit being worked upon, therefore, indicating that the item under test has no dead short connections. The Red LoZ LED illuminates to indicate an Impedance of less than 100 ohms has been detected. An operative would immediately know not to proceed and to conduct further investigation. The Green HiZ LED illuminates to indicate a high Impedance of more than 100 ohms ensuring that the engineer is safe to re-energise the meter.

An additional problem can be ghost or induced voltage. Most 2 pole testers which allow you to test for ghost voltages do this by varying the load on the circuit by depressing two buttons, one on the main tester and the other on the passive probe. This instrument does this automatically and has no buttons to depress.

It should be proved both before and after use on an AC Output Proving Unit such as the SP400.

Features

  • Clear and Unique Circuit Impedance Indication for added safety
  • Front dual; high visibility, colour coded LED display of voltage and hi/lo impedance
  • Secondary base display for safe arms-length indication
  • Interchangeable straight and right-angled GS38 compliant test prods
  • No batteries and no buttons for simple, reliable operation
Operating Voltage Range 50 - 600V AC
LED Indication 50 - 110 - 230 - 400V LED illuminates at nominal value -15%
Withstand Voltage 600V
Operating Conditions -10 to +55°C at 85% RH
Altitude up to 2000m
Overvoltage Category CAT IV 600V
Operating Current < 3.5mA
Operating Duty Cycle 30s on, 240s off
Impedance Measurement HiZ threshold 100Ω
Circuit loading meets the requirement of BS EN 61010-1:2010 Figure 2.
IP Rating IP54
Safety Compliance BS EN 61010-2-030:2010
EMC Compliance BS EN 61326-2-2:2013
Prods GS38 Compliant
Main unit: straight or right-angle interchangeable
Dimensions 320H x 75W x 35D (mm)
Interconnecting Cable 1.3m Silicone rubber, Double insulated, Wear indicating 690V continual rating, Tested to 6.5 kV
Weight 200g
Batteries Not Required
Write Your Own Review
You're reviewing:Socket & See VIPESI Electrical Service Industry Safety Two Pole Tester